Clopay Torsion Spring Replacement Nationwide

Clopay Torsion Spring Replacement: The Fort Worth Owner’s Guide

We replace Clopay torsion springs across Fort Worth, and the installed price for a spring replacement on a Clopay door typically runs $180 – $340 depending on spring size, cycle rating, and whether one or two springs need attention. Same-day service is available on most spring calls, and the tech arrives with Clopay-compatible springs and the wind bars to do the job right the first time. You’ll usually discover the failure the hard way: a bang from the garage that sounds like a car backfiring, then a door that won’t lift no matter how many times you press the remote.

Call (682) 432-0305

Which Clopay Models This Applies To

Clopay builds doors under several lines that roll through Fort Worth garages constantly: the Gallery series, the Coachman carriage-house line, the Bridgeport, the Value Plus, and the heavier commercial-grade models. The funny thing about Clopay is that their residential doors often ship with one of a few common torsion spring wire sizes, so the spring on a Gallery steel door may be nearly identical to one on a Coachman. What actually matters is three numbers printed on the spring cone: wire diameter, inside diameter, and length. If the label is faded or painted over, we measure the old spring directly. Clopay’s OEM springs are solid, but they don’t make springs themselves; they source them from major spring manufacturers. A quality aftermarket spring rated for the same cycles and wire gauge performs just as well and often gives us more flexibility on cycle rating. The real compatibility gotcha is wind load: doors in areas like Saginaw or Weatherford that sit exposed catch more north Texas wind, and Clopay doors in those spots often need springs wound for a heavier door weight than the tag suggests. We verify the door’s actual weight before selecting springs, not just the old spring’s size.

Signs Your Clopay Torsion Spring Replacement Is Failing

• A loud bang from the garage. That’s the spring snapping under tension. It’s unmistakable, and the door will usually thud down or refuse to move afterward.
• The door feels unusually heavy when you try to lift it manually. With a broken spring, the opener is doing all the work it was never designed to do. Continuing to run it will burn out the motor.
• A gap in the spring itself. Look up at the coil above the closed door. If you see a clean separation between sections of the coil, that spring is done.
• The door opens a few inches, then stops or reverses. The opener’s force sensor detects the extra weight and cuts power as a safety measure.
• Uneven movement or a crooked door. On a two-spring door, one spring failing leaves the other doing double duty, and the door starts to twist or bind in the tracks.

Replacement Cost & What’s Included

In Fort Worth, a single torsion spring replacement on a Clopay door runs $180 – $340 installed. Most residential doors use two springs, and when one breaks, we recommend replacing both: they’ve cycled the same number of times, and the second spring usually fails within weeks. The price includes the spring, the winding, the labor, and a full safety check of the door balance and opener force settings. What moves the number within that range is spring size and cycle rating: a 10,000-cycle spring costs a bit more than the standard 5,000-cycle unit, but it buys you roughly double the lifespan. You’ll get a written price before any work starts, and the invoice won’t shift after the fact. Jaylen Ross built our whole operation on that principle, and we don’t compromise it.

DIY or Call Us?

Here’s the straight answer: torsion springs are the one garage door component we tell people not to touch. They store an enormous amount of energy, and when a winding bar slips, that energy releases through the bar with enough force to cause serious injury. What you can safely do on your own: check the spring visually for cracks or gaps, confirm whether the door operates manually in balance, and note the model number on the door sticker before calling us. The rest is a trained technician’s job with the right tools, the right spring, and the experience to set the tension correctly. Tell us what it’s doing, and we’ll tell you what it needs. Call (682) 432-0305 and a live person answers, day or night.

FAQs